A smart lock only works as well as the door it sits on, so inspect the door before you pick a product. Check five things in order: whether the door closes and latches without force, whether the current bolt slides freely, whether the door and frame are solid where the lock mounts, what happens to the existing lock, and who still needs a physical key.
Facts to gather about the door before you shop
Start with what you can see and measure at home. Note the door material (wood, metal-clad, or solid metal), whether glass sits near the lock, and the thickness, measured on the door edge with the door open. Note whether it is a single hinged door or one of a pair, and whether it is an entry door, an interior door, a business entrance, or a door shared by several units.
Then name the lock already there. A deadbolt is the separate bolt worked by a key outside and a thumb turn inside. A handle set or knob uses a spring latch, the angled tongue that clicks shut on its own. Older doors sometimes have a mortise lock instead: one box-shaped lock body set into a pocket cut into the door edge. Many smart deadbolts are made to fit the round holes a standard deadbolt uses, so this detail shapes your options.
Some details are hard to judge from home. What is inside the door around the lock, how the frame is built behind the trim, and whether old holes are worn or oversized are things an installer should confirm on site.
Five checks, in order
Each step either clears the door to move on or tells you to fix something before electronics go on.
1. Does the door close without help?
Close the door gently. It should latch without you lifting the handle, leaning on it, or slamming it. Rubbing, a drooping latch side, or a needed shoulder push points to hinges, the frame, or swelling. That is a fix-first problem, because a motor cannot lift or shove a door the way your hand does.
2. Does the current bolt slide freely?
Turn the deadbolt with the door open, then again with it closed. If the bolt is smooth when open but stiff when closed, it is catching on the strike plate, the metal plate in the frame that the bolt slides into. A smart deadbolt moves its bolt with a small motor, and a binding bolt stalls that motor and runs the batteries down faster. Repair the alignment first.
3. Is the door solid where the lock mounts?
Look for cracks, soft wood, leftover holes from old locks, or a split frame near the strike. The interior unit of a smart lock is bulkier than a thumb turn and needs a flat, sound surface to sit on. Damage here means repair before anything new is installed.
4. Keep, replace, or pair the current lock?
You can swap the deadbolt for a smart one, add a keypad, or keep the current lock and fit a smart unit that works with it. If you want to keep an existing high-security cylinder and its keys, say so early, because that narrows the choices. A mortise lock usually means fewer drop-in options.
5. Who still needs a physical key?
Decide who needs a way in if the batteries die or the electronics fail. Going fully keyless is a choice to make on purpose, not by default.
How the door gets used changes the right lock
Traffic sets the priorities. A door opened all day by family, staff, or deliveries suits a keypad anyone can work quickly, rather than a lock that depends on each person having a phone app. A side door used once a week asks much less of the hardware.
Weather exposure matters too. A keypad facing open rain and sun takes more wear than one under an overhang or inside a vestibule, so note which way the door faces and what shelters it.
Then list who comes in: guests, cleaners, dog walkers, employees, tenants. Each group raises the question of separate codes and whether you can remove one person's access without disturbing anyone else. Smart locks differ a lot in how they handle that. A business entrance or a shared door with a buzzer often calls for commercial hardware or access control rather than a single residential lock.
What to hand a locksmith
Bring these notes to the conversation:
- Home or business, and private or shared entry
- Door material, thickness, and any glass near the lock
- Current lock: deadbolt, handle set, both, or mortise
- Problems found in the five checks
- Whether the existing lock stays, goes, or gets paired
- Who needs access by code, app, or key, and who holds the backup key
Williamsburg Locksmith and Key Copy is a mobile locksmith that comes to doors in Williamsburg, Greenpoint, Bushwick, Bed-Stuy, East Williamsburg, and Downtown Brooklyn, as well as elsewhere in Brooklyn and in Manhattan, Queens, the Bronx, and Staten Island. To talk through smart lock and keypad options for your door, and any repair it needs first, call (347) 699-9268.
Frequently asked questions
Can I keep my existing deadbolt and just add a keypad or smart unit?
Often, yes. Some smart units replace only the interior thumb turn of an existing deadbolt and leave the outside cylinder and keys as they are. Others pair a keypad with a separate deadbolt. Either route depends on the deadbolt's type and condition and the flat space around the thumb turn. A worn or binding deadbolt should be repaired or replaced first.
Should I fix a sticking door before or after installing a smart lock?
Fix a sticking door before the smart lock goes on. A smart lock's motor moves the bolt but cannot pull the door tight against the frame, so a sticking door leads to bolts that stop partway and locks that report a jam. If the door only sticks in certain seasons, test it when it is at its worst and mention that pattern to whoever handles the repair.
Do I still need a physical key with a smart lock?
For most doors, a physical key is the sensible backup, because smart locks run on batteries and electronics that can fail. Keep at least one key somewhere you can reach from outside the locked door, such as with a neighbor or family member. Some keypad-only models have no key cylinder at all, so confirm one is present before buying.
What should I photograph or note about my door before calling a locksmith?
Photograph each face of the door straight on with the whole lock visible, the door edge with the door open showing the bolt and latch, and the frame where the strike plates sit. A shot with a tape measure across the door edge records the thickness. Add one wide photo of the doorway so a locksmith can see glass, trim, and any overhang above the door.