A hinged door lock secures a door that swings by throwing a bolt straight out of the door edge into a strike plate on the frame. A sliding patio door lock secures a panel that rolls sideways in a track, so it swings a hook out of the panel's edge to catch a keeper, a metal catch on the frame. The door's movement decides which design works.
The hinged door lock as a baseline
A hinged door swings on hinges along one edge. The lock's job is to put metal across the gap between the opposite edge and the frame so the door can't swing open.
Most entry doors use two bolts. The latch is the spring-loaded tongue with a slanted face. It slides back as the door closes, then pops into the strike plate, the metal plate with a hole fixed to the frame. The deadbolt has no spring and a square end. A key or thumbturn throws it out, and pressure on its end won't push it back. The cylinder is the part the key enters, and its internal pins let it turn only for the right key.
A hinged door has room for a deep bolt. The door is thick and the frame is solid, so the frame can hold a strike with a pocket behind it. Push on a locked door and the bolt is pressed sideways into the frame, a load a bolt handles well.
Inside a sliding door lock: hook, keeper, track
A sliding patio or balcony door doesn't swing. The panel rests on small wheels called rollers, which ride in a track along the sill, and the whole panel travels sideways to open.
The sliding door lock lives in the stile, the vertical frame piece along the edge of the glass. The stile closes against the jamb, the upright side of the door frame. On the inside you'll see a handle set with a small lever, and some doors add a key cylinder outside. Flip the lever and a hook swings out of the stile's edge into the keeper, a metal catch screwed to the jamb. With the hook behind the keeper, pulling the panel sideways pulls the hook against the keeper instead of opening the door.
Many sliding door locks are mortise locks, meaning the lock body sits in a pocket cut into the stile. The stile is narrow, often hollow metal or vinyl with glass close by, so there's little room for a large lock body or a long bolt. The hook gets its hold by turning and catching, not by reaching deep.
Why can't a deadbolt go on a sliding glass door?
Direction is the main reason. A deadbolt throws straight out of the door's edge. On a hinged door, that blocks the swing. On a sliding door, a straight bolt points the same way the panel moves when it opens, so the panel would draw the bolt right back out of its hole. The curve of a hook is what lets a sliding door lock resist that pull.
Mounting is the second reason. A standard deadbolt needs a wide, solid door to bore through, and a sliding door's stile usually can't take that hole without cutting into the frame that holds the glass.
The forces differ as well. A sliding panel sits on rollers in a track, so it can lift or shift slightly, and when the panel moves, the hook moves with it relative to the keeper. That is why a sliding door lock often feels looser than a front door lock, and why it can seem broken when it isn't. Worn rollers let the panel ride low, so the hook meets the keeper off center. A bent keeper or a loose handle set throws the fit off too.
What to check on each door
Look at both doors from the inside, closed and locked. On the sliding door, watch the lever as you flip it. The hook should seat behind the keeper, not stop short or spring back. Sight along the panel to see whether it closes flush against the jamb or rides higher at one end, then press on the handle set and the keeper to feel for play. On the hinged door, the deadbolt should throw all the way without dragging on the strike plate.
If the lever moves but the hook doesn't come out, the lock body is the likely suspect rather than the fit.
A loose handle set, a bent keeper, or a hook that won't catch is door hardware and repair work. Lock change and rekey, high-security locks, and smart locks or keypads are separate questions, and whether any of them suits a particular sliding door depends on the hardware already there and what the stile and frame can accept. Williamsburg Locksmith and Key Copy is a mobile locksmith that offers each of these services, and you can call (347) 699-9268 to talk through what you're seeing.
Frequently asked questions
Can a sliding door lock be keyed to match my other locks?
Many sliding door locks lock only from the inside and have no key cylinder at all. Where a sliding door does have an outside cylinder, whether it can take the same key as your other locks depends on that cylinder's design, so the answer varies by door. Williamsburg Locksmith and Key Copy offers lock change and rekey, and you can ask whether that applies to your sliding door.
Why does my sliding door lock sometimes not catch even though it looks closed?
A sliding door can look shut while stopping just short of the jamb, so the hook swings past the keeper instead of behind it. Debris in the bottom track, stiff weatherstripping, worn rollers, or a keeper that has shifted can each cause this. If the sliding door lock catches after you slide the panel firmly closed, the fit is the issue, not the lock.
Are smart locks or keypads available for sliding doors?
Some smart locks and keypads are made for sliding doors, but they don't fit every sliding door. A narrow stile, the handle set layout, and the way the hook meets the keeper limit what can be mounted. Williamsburg Locksmith and Key Copy offers smart locks and keypads, and compatibility depends on the specific door and frame.
Is a sliding door lock repair different from a hinged door lock repair?
A sliding door lock repair involves different parts than a hinged door lock repair. Hinged door trouble often traces to a sagging door, a strike plate out of line, or a worn latch or cylinder. Sliding door trouble often involves the panel's position in its track, the rollers, the keeper, or the handle set. Both are door hardware work.